Repeated low-velocity impact responses of SiC particle reinforced Al metal-matrix composites

This study aimed to investigate experimentally the repeated low-velocity impact behaviors of SiC reinforced aluminum 6061 metal-matrix composites for different volume fractions and energy levels. In addition, the hardness variations were measured by the Vickers hardness tests from the impacted and impact-free cross-sections of the particle reinforced metal-matrix composites. Low-velocity impact tests were applied to composite samples manufactured by powder metallurgy (in 10, 20, and 30% volume fractions) at two total energy levels (15 and 60 J as single) and in repetitions equal to the sum of these energy levels (5 + 5 + 5 and 20 + 20 + 20 J as repeated). As a result, in increasing the impact number for all volume fractions, the total contact time was shortened and the peak contact force increased, whereas both the permanent central deflection and the absorbed energies reduced. Hence, these variations obtained under repeated impacts (5 + 5 + 5 and 20 + 20 + 20 J) revealed that metal-matrix composites showed a tougher behavior with an increase in the impact numbers from 1st to 3rd, particularly because of the strain hardening effect. Furthermore, an increase in volume fraction from 10 to 30% resulted in an increase in the impact strength under all repeated and single impacts despite changing deformation and damage mechanisms due to increasing the strain hardening effect and particle fractures. The hardness was affected by the volume fraction and increased as the volume fraction increased in both the impacted and impact-free zones. The repeated impact increased the impacted zone hardness more than the single impact for all volume fractions. Additionally, the hardness of the impacted zone under 20 + 20 + 20 J repeated impact was measured as the highest value in the 30% volume fraction. Therefore, metal-matrix composites can behave harder with the strain hardening effect under repeated impacts.     

A comparative study on the effect of carbon-based and ceramic additives on the properties of fiber reinforced polymer matrix composites for high temperature applications

Ablative composites have been in use for thermal protection of space vehicles for decades. Carbon-phenolic composites have proven to perform exceptionally well in these applications. However with development in aerospace industry their performance needs improvement. In this field, different carbon-based and ceramic additives have been introduced into ablative composite systems. This review article gives a comparative analysis of researches done in this field in the recent past. Density, ablative, thermal and mechanical properties of ablative composites with different ultra-high temperature ceramic particles i.e. ZrSi₂, Cenosphere, nano-SiO₂, BN etc. and carbon-based nanoparticles i.e. CNTs, nano-Diamonds, Graphene oxide etc. used as additives, have been compared and discussed. Emphasis is put on carbon-phenolic composite systems although some epoxy matrix systems have also been discussed for comparison.     

双亲纳米SiO2颗粒的制备及提高渗吸采收率性能

以正辛基三乙氧基硅烷和3-巯基丙基三乙氧基硅烷为改性剂，以双氧水为氧化剂，在水基环境下对亲水纳米SiO2颗粒表面进行改性，得到具有磺酸基和辛基的双亲纳米SiO2颗粒，并通过红外和热重对其化学结构和热稳定性进行分析。将双亲纳米SiO2颗粒分散在地层水中制备纳米流体，并评价纳米流体的稳定性、界面性质和渗吸效率。利用核磁共振技术探究纳米流体渗吸过程中岩心孔隙内原油运移规律。结果表明，纳米流体储存30 d未出现分层现象，表现出良好的稳定性；经纳米流体处理的岩心亲水性增强。此外，双亲纳米SiO2颗粒将油水界面张力降低至1.7 mN/m；纳米流体渗吸采收率高达22.6%，渗吸初始阶段小孔隙中的原油被动用，而在渗吸后期阶段大孔隙中的原油才被动用。     

Effects of SiC,Al2O3, and ZrO2 particles on the LBMed characteristics of Al/SiC,Al/Al2O3, and Al/ZrO2 MMCs prepared by stir casting process

The effects of SiC, Al₂O₃, and ZrO₂ particles on the characteristics of Al/SiC, Al/Al₂O₃, and Al/ZrO₂ metal matrix composites (MMCs) have been studied in the present research work. The comparison of machining characteristics has been done to analyze the behavior of various reinforced particles with the variation of laser machining variables. The output characteristics such as dross height and kerf deviation have been investigated and compared with each MMCs. SEM and XRD have been used for the investigation of morphological changes in the structure and agglomeration of reinforced particles. The crack and recast layer formation has been examined in the specimens of higher quantity of reinforced particles. It was observed that the MMC material reinforced with SiC particles has shown different behavior as compared to other MMC materials.     

Subunit-based mucosal vaccine delivery systems for pulmonary delivery - Are they feasible?

Pulmonary infections are the most common cause of death globally. However, the development of mucosal vaccines that provide protective immunity against respiratory pathogens are limited. In contrast to needle-based vaccines, efficient vaccines that are delivered via noninvasive mucosal routes (such as via the lungs and nasal passage) produce both antigen-specific local mucosal IgA and systemic IgG protective antibodies. One major challenge in the development of pulmonary vaccines using subunit antigens however, is the production of optimal immune responses. Subunit vaccines therefore rely upon use of adjuvants to potentiate immune responses. While the lack of suitable mucosal adjuvants has hindered progress in the development of efficient pulmonary vaccines, particle-based systems can provide an alternative approach for the safe and efficient delivery of subunit vaccines. In particular, the rational engineering of particulate vaccines with optimal physicochemical characteristics can produce long-term protective immunity. These protect antigens against enzymatic degradation, target antigen presenting cells and initiate optimal humoral and cellular immunity. This review will discuss our current understanding of pulmonary immunology and developments in fabricating particle characteristics that may evoke potent and durable pulmonary immunity.     

A Novel Strategy for Preparing Stretchable and Reliable Biphasic Liquid Metal

Low‐melting liquid metal is a hugely promising material for flexible conductive patterns due to its excellent conductivity and supercompliance, especially low‐cost and environmental liquid processing technology. However, the ever‐present fluidity characteristic greatly limits the stable shape and reliability of prepared liquid metal conductive electronics. Herein, a novel solidification strategy of liquid GaIn alloys by Ni doping and heat treatment is first reported, which can efficiently create a solid phase in the liquid metal and provide an effective solution for practical applications. Particularly, the liquid characteristic is preserved for conveniently fabricating different flexible electronic circuits, and then the solidification is carried out on prepared conductive patterns by heat treatment. The solidification mechanism is revealed by the interface chemical reaction between Ni and GaIn, creating the solid phase of intermetallic compound (Ga₄Ni₃ and InNi₃) during heat treatment. Moreover, a biphasic GaInNi can be obtained by regulating the atomic ratio of gallium, indium, and nickel. As a result, the obtained GaInNi possesses extremely low sheet resistance (15 ± 4.5 to 135 ± 2.5 mΩ sq^?1) and the variation of ΔR/R₀ exhibits low level (0–2) when strained up to 100%, which offers a promising strategy to prepare stretchable and reliable liquid metal electronics.     

Hydrogen production by oxidative steam reforming of methanol over anodic aluminum oxide-supported Cu-Zn catalyst

Oxidative steam reforming of methanol (OSRM), which is a convenient reaction for producing hydrogen, suffers from the hot spot formation problem when conventional particle catalysts are used. Recently, an anodic aluminum oxide (AAO)-supported Cu-Zn catalyst was proposed as an OSRM catalyst for its high thermal conductivity through the aluminum metal body. In this study, OSRM was conducted in a prototype reactor packed with the AAO plate catalyst strips. It was verified that the high thermal conductivity of the catalyst effectively suppresses the hot spot formation and makes the temperature profile smooth along the reactor. The start-up time of the reactor depended on the preheating temperature and was very short (less than 2 min) for preheating over 503 K. The methanol conversion and reactor temperature increased with increasing O₂/CH₃OH mole ratio, indicating that the mole ratio can be used as a control variable to operate the reactor at desired conditions. Further, a reactor model was developed and verified, and the simulation showed that for a given total reactor volume, an optimal reactor configuration could be achieved by shortening the reactor length while widening the cross-sectional area.     

Highly transparent low resistance ATO/AgNWs/ATO flexible transparent conductive thin films

Indium-free flexible transparent conductive thin films (TCFs) composed of silver nanowire (AgNW) networks and Sb doped SnO₂ (ATO) layers were prepared on polyethylene terephthalate (PET) substrates. The ATO layers were deposited via radio frequency (RF) magnetron sputtering at room temperature. The AgNWs were achieved via a modified polyol reduction method and embedded between the ATO layers. The effects of AgNW networks and ATO layers on electrical and optical properties of the ATO/AgNWs/ATO flexible tri-layer thin films are investigated. The ATO layers can improve the optical transmittance and reduce the resistivity of tri-layers, and the corresponding mechanisms are proposed. Typically, an ATO/AgNWs/ATO flexible tri-layers show a high figure of merit value (30.06 × 10^-3 Ω^-1) with a low sheet resistance of 7.1 Ω/sq. and a high transmittance of 85.7%. Meanwhile, the tri-layers present excellent mechanical flexibility, and the ATO layers acted as the protecting layers improve the adhesive and environmental stability at high temperature and humidity for the ATO/AgNWs/ATO flexible tri-layers. These results indicate that ATO/AgNWs/ATO flexible tri-layer thin films can be useful for the fabrication of wearable electronic devices.     

Polystyrene latex particles bearing primary amine groups via soap‐free emulsion polymerization

Polystyrene latexes were prepared in the presence of an amino‐containing functional comonomer, N‐(3‐aminopropyl)methacrylamide hydrochloride (APMH), via soap‐free batch emulsion polymerization initiated by the cationic initiator 2,2′‐azobis(2‐amidinopropane) dihydrochloride. These latexes were characterized by studying the influence of the ionic comonomers on the polymerization kinetics, particle size, surface charge density and colloidal properties. The synthesized latexes were monodisperse with a final size between 100 and 600 nm depending on the APMH concentration. The initial polymerization rate and the particle number increased in accordance with the Smith–Ewart theory for soap‐free styrene emulsion polymerization with a hydrophilic functional comonomer. The final functionalization rate of the particles has been particularly studied with the intention of fitting the prepared latexes to be used in the immobilization of biological molecules for biological sample preparation and diagnostic applications. © 2020 Society of Chemical Industry     

Influence of zinc and cadmium co-doping on optical and magnetic properties of cobalt ferrites

Zinc and cadmium based cobalt ferrites Zn_xCd_0.375-xCo_0.625Fe₂O₄ (where x = 0, 0.075, 0.125, 0.25) were successfully synthesized by a facile co-precipitation technique. Structural, optical and magnetic characteristics of the doped ferrites were systematically analyzed. X-ray Diffraction (XRD) pattern confirmed the formation of cubic spinel structure in all samples. Scanning electron microscopic analysis of surface morphology revealed cubic and spherical shaped ferrite particles. Fourier transform infrared (FTIR) spectroscopy confirmed the existence of metal oxygen (M − O) bonding in the prepared samples. Moreover, the prepared samples exhibited two frequency bands corresponding to phonon vibrational stretching in both octahedral and tetrahedral lattice positions. The optical properties were investigated in detail through photoluminescence (PL) spectroscopy and Raman spectroscopy. The PL spectrum confirmed the strong emission peaks in the ultraviolet to visible region of all the samples. Further, four active Raman modes, associated with cubic spinel structure are identified in all prepared samples. Finally, the magnetic characteristics are evaluated by using vibrating sample magnetometer (VSM) revealing ferrimagnetic and soft magnetic behavior of the samples. As the Zn and Cd co-doping in Co was increased, the H_c was decreased. The magnetic studies show the maximum H_c of 576 Oe for Cd doped cobalt ferrite, and maximum saturation magnetization (M_s) for Zn–Cd doped cobalt ferrite. It is envisaged that the newly prepared Zn–Cd co-doped cobalt ferrite would be appropriate for a number of important applications, for example, magnetic recording devices, sensors, actuators, high-density data storage devices, and biomedical equipments.